Sink hookup

sink hookup

How do you connect a sink to a kitchen sink?

Connect your sinks As shown in the image below, use a connecting pipe to join up the plumbing. This should be above your P-trap and drain as all the water needs to flow down a single route. Connect the pipe between the kitchen sinks and secure it in place using a connector ring, nuts, and bolts.

How to install a pop-up sink drain?

The pop-up is the device that allows you to open and close the sink drain, usually made of a simple metal rod with ball attached to it. Drop stopped into sink from top, slide short end of rod into the opening on the tailpiece, making sure that the opening for the ball is facing toward the lever for the pop-up. Install as per the instructions.

Can a sink be installed under a house?

If it doesnt, you may need to do some trimming or cut the entire opening if youre installing a sink in a house under construction. Most new sinks come with clips and screws that are used to hold the sink in place. If you buy a faucet, sometimes itll come with the drain and tailpiece for the sink.

How to connect a portable washer to a sink?

Take the water hose and connect it to the quick connector. Note: Make sure you tighten the connection using the pliers. Now connect one end of the water hose connector to the sink and the other end with your portable washer. 1.) Now connect the drain hose (Don’t forget to attach the clamp), And squeeze the clamp to tighten it further.

How to install a sink in the kitchen?

How to Install a Kitchen Sink 1 Check the Countertop Opening. Set the new sink in the countertop hole to verify that it fits. ... 2 Attach the Clips 3 Install the Faucet 4 Install the Strainer 5 Secure the Gaskets 6 Clean Up 7 Install the Disposal Mount 8 Seal the Basin 9 Set the Sink in Place 10 Secure the Hardware More items...

How do you connect two sinks to one drain?

There will only be one connection to the drain, so you need to connect the two sinks together in the plumbing. Install and plumb your sinks using the steps above for a single basin sink, but remember to use a Tee fitting so you can install another connecting pipe.

Can I hook up a washing machine to a kitchen sink?

Can I Hook Up a Washing Machine to a Kitchen Sink? 1 Two Important Code Issues to Remember. The output from a washing machine is under pressure, and a standard 1 1/2-inch sink P-trap assembly is too small to handle it. 2 A Safe Way to Drain the Washing Machine. ... 3 Install a Male-to-Male Faucet Adapter for the Water Supply. ...

How to plumb a double kitchen sink?

Plumbing A Double Kitchen Sink 1 1#N#Install your strainers#N#Install and plumb your sinks using the steps above for a single basin sink, but remember to use... 2 2#N#Connect your sinks#N#As shown in the image below, use a connecting pipe to join up the plumbing. This should be above... More ...

Discuss Sockets under Sink ? in the Electrical Forum area at ElectriciansForums.net Most new kitchens you seem to have no option but to install sockets (for wash machine/dish washer etc) under the sink in the base unit.

How to connect washing machine to kitchen sink?

Connecting a Washing Machine to a Kitchen Sink. 1 Step 1: Extension Hoses. None of the hoses that came with the washer are long enough to reach the sink. The supply hose is female hose fitting (both ... 2 Step 2: Sink Connection. 3 Step 3: Connection to the Washing Machine. 4 Step 4: Finishing Setup. 5 Step 5: Wrap-up. More items

How do you connect a portable washer to a regular washer?

Connecting with a portable machine Attach the drain hose to the back of the washer’s drain outlet. On most portable washers, the drain hose has a friction clamp at one end and a hose connector at the other end. Compress the tension clamp with the help of pliers and drive over the drain port until the washer cabinet is reached by the hose.

Can the washer hose reach the sink?

None of the hoses that came with the washer are long enough to reach the sink. The supply hose is female hose fitting (both ends)--I just cobbled one together out of plastic hose repair fittings and clear braided tubing (all available from Home Depot).

How do I connect the water hose to the sink?

If the sink has an external threads, remove the rubber washer. Take the water hose and connect it to the quick connector. Note: Make sure you tighten the connection using the pliers.

Related posts: