Atv winch hook up

atv winch hook up

How to wire a winch to an ATV?

The wire routing should be conducted in such a way so that no wires can be caught on any moving equipment or debris when the ATV is under operation. Connect the yellow cable to the #1 connector on the winch. Attach the blue cable to the #2 connector on the winch. Use the torque wrench and the correct-sized socket.

How do I attach the Blue cable to the winch?

Attach the blue cable to the #2 connector on the winch. Use the torque wrench and the correct-sized socket. Tighten the terminal nuts on the winch to 50 pound-inches.

How do you hook up a remote control to an ATV?

Hook up the other set of wires from the Handle-bar switch to the Solenoid box so you can use the winch even if your ATV is switched off. If you want to connect the wired remote control, now is the time to draw up the cables together with all the other wires and cables being installed.

What is a winch mounting plate?

A winch mounting plate attaches your winch to the mounting bracket and to the front bumper of your ATV. They are designed to withstand the tension of pulling your ATVs out. You will need to have a specific winch mount that holds the winch without any hassles. Most winches include a winch mount that may or may not fit all vehicles.

How to wire a Warn winch on an ATV?

How to Wire a Warn Winch on an ATV. Tie the black wire to the black wire and the green wire to the green wire connectors. Connect the cables from the battery in the following order to the posts on the contactor relay. Attach the red cable from the battery positive (+) terminal to the red connector on the relay.

How to wire a winch to a battery?

1 Attach the power wire to the positive post on the winch 2 Attach the negative wire to the negative ground post on the winch 3 Run both wires from the winch to the battery compartment, avoiding hot areas and places where the wires could get pinched

How do you run a winch on a trailer?

The easiest way to run a winch on a trailer using the battery in your vehicle is to install a quick disconnect at the rear of your truck. This is Option 1 under Wiring a Trailer-Mounted Winch.

How do you hook up a remote control to an ATV?

Hook up the other set of wires from the Handle-bar switch to the Solenoid box so you can use the winch even if your ATV is switched off. If you want to connect the wired remote control, now is the time to draw up the cables together with all the other wires and cables being installed.

What size is a winch mount plate?

Like the other universal plates, it has a 10 x 4.5 mounting pattern for mounting foot-down winches. The fairlead holes are 10 apart on center but it also includes a patch plate that you can use to work with a smaller utility winch roller fairlead. This is a tame, light winch mount plate that is has a black epoxy finish. Fits foot-down winches.

How do you mount a winch to a car?

Mount The Mounting Plate: Align the winch perpendicular to the centerline of the vehicle at the desired location. Mark the location of the winch base holes. Then install the mounting plate by bolting it securely. Mount The Winch: Simply mount the winch into the mounting plate and secure tightly with bolts.

Can I use helicoil mounting plates to mount a winch?

If you do strip your threads, use Helicoil to repair them and buy a torque wrench like you should have in the first place. These mounting plates are fine for mounting most winches regardless of brand, as long as the orientation is correct and they have the standard 10 x 4.5 mounting pattern.

What size winch mount do I need for a hawse?

The Driver winch mounting plate is good for foot-down winches and includes a spot for your hawse or roller fairlead. It has a standard winch mount pattern and a standard fairlead mount. Its 22 7/8 wide and 7 1/8 deep and will bolt down on flat areas and between some framerails.

Related posts: